问答
产品
|
公司
|
配件目录
|
EPC底盘号查询
下载手机汽配人
汽配人首页 >
问答首页
急求磁悬浮轴承或磁悬浮飞轮英文资料及译文
要求译文字数在3000字以上,谢谢!!
问
提问者:网友
|
2017-06-02
最佳回答
Magnetic Bearing A magnetic bearing is a bearing which supports a load using magnetic levitation. Magnetic bearings support moving machinery without physical contact, for example, they can levitate a rotating shaft and permit relative motion without friction or wear. They are in service in such industrial applications as electric power generation, petroleum refining, machine tool operation and natural gas pipelines. They are also used in the Zippe-type centrifuge used for uranium enrichment. Magnetic bearings support the highest speeds of any kind of bearing; they have no known maximum relative speed. Description It is difficult to build a magnetic bearing using permanent magnets due to the limitations imposed by Earnshaw's theorem, and techniques using diamagnetic materials are relatively undeveloped. As a result, most magnetic bearings require continuous power input and an active control system to hold the load stable. Because of this complexity, the magnetic bearings also typically require some kind of back-up bearing in case of power or control system failure. Two sorts of instabilities are very typically present with magnetic bearings. Firstly attractive magnets give an unstable static force, decreasing with greater distance, and increasing at close distances. Secondly since magnetism is a conservative force, in and of itself it gives little if any damping, and oscillations will cause loss of successful suspension if any driving forces are present, which they very typically are. With the use of an induction-based levitation system present in cutting-edge MAGLEV technologies such as the Inductrack system, magnetic bearings could do away with complex control systems by using Halbach Arrays and simple closed loop coils. Basic Operation Basic Operation for a Single AxisAn active magnetic bearing (AMB) consists of an electromagnet assembly, a set of power amplifiers which supply current to the electromagnets, a controller, and gap sensors with associated electronics to provide the feedback required to control the position of the rotor within the gap. These elements are shown in the diagram. The power amplifiers supply equal bias current to two pairs of electromagnets on opposite sides of a rotor. This constant tug-of-war is mediated by the controller which offsets the bias current by equal but opposite perturbations of current as the rotor deviates by a small amount from its center position. The gap sensors are usually inductive in nature and sense in a differential mode. The power amplifiers in a modern commercial application are solid state devices which operate in a pulse width modulation (PWM) configuration. The controller is usually a microprocessor or DSP. Applications Magnetic bearing advantages include very low and predictable friction, ability to run without lubrication and in a vacuum. Magnetic bearings are increasingly used in industrial machines such as compressors, turbines, pumps, motors and generators. Magnetic bearings are commonly used in watt-hour meters by electric utilities to measure home power consumption. Magnetic bearings are also used in high-precision instruments and to support equipment in a vacuum, for example in flywheel energy storage systems. A flywheel in a vacuum has very low windage losses, but conventional bearings usually fail quickly in a vacuum due to poor lubrication. Magnetic bearings are also used to support maglev trains in order to get low noise and smooth ride by eliminating physical contact surfaces. Disadvantages include high cost, and relatively large size. A very interesting new application of magnetic bearings is their use in artificial hearts. The use of magnetic suspension in ventricular assist devices was pioneered by Prof. Paul Allaire and Prof. Houston Wood at the University of Virginia culminating in the first magnetically suspended ventricular assist centrifugal pump (VAD) in 1999 History The evolution of active magnetic bearings may be traced through the patents issued in this field. The table below lists several early patents for active magnetic bearings. Earlier patents for magnetic suspensions can be found but are excluded here because they consist of assemblies of permanent magnets of problematic stability per Earnshaw's Theorem. Early active magnetic bearing patents were assigned to Jesse Beams at the University of Virginia during World War II and are concerned with ultracentrifuges for purification of the isotopes of various elements for the manufacture of the first nuclear bombs, but the technology did not mature until the advances of solid-state electronics and modern computer-based control technology with the work of Habermann and Schweitzer[5]. Extensive modern work in magnetic bearings has continued at the University of Virginia in the Rotating Machinery and Controls Industrial Research Program. The first international symposium for active magnetic bearing technology was held in 1988 with the founding of the International Society of Magnetic Bearings by Prof. Schweitzer (ETHZ), Prof. Allaire (University of Virginia), and Prof. Okada (Ibaraki University). In 1987 further improved AMB designs were created in Australia by E.Croot but these designs were not manufactured due to expensive costs of production. However, some of those designs have since been used by Japanese electronics companies, they remain a speciality item: where extremely high RPM is required. Since then there have been nine succeeding symposia. Kasarda reviews the history of AMB in depth. She notes that the first commercial application of AMB’s was with turbomachinery. The AMB allowed the elimination of oil reservoirs on compressors for the NOVA Gas Transmission Ltd. (NGTL) gas pipelines in Alberta, Canada. This reduced the fire hazard allowing a substantial reduction in insurance costs. The success of these magnetic bearing installations led NGTL to pioneer the research and development of a digital magnetic bearing control system as a replacement for the analog control systems supplied by the American company Magnetic Bearings Inc. (MBI). In 1992, NGTL's magnetic bearing research group formed the company Revolve Technologies Inc[1]. to commercialize the digital magnetic bearing technology. This firm was later purchased by SKF of Sweden. The French company S2M, founded in 1976, was the first to commercially market AMB’s. Extensive research on magnetic bearings continues at the University of Virginia in the Rotating Machinery and Controls Industrial Research Program Magnetic bearings support moving machinery without physical contact, for example, they can levitate a rotating shaft and permit relative motion without friction or wear. Long considered a promising advancement, they are now moving beyond promise into actual service in such industrial applications as electric power generation, petroleum refining, machine tool operation and natural gas pipelines. The AVCON magnetic bearing permits motion without friction or wear. Among companies producing advanced magnetic bearing systems for industrial use is AVCON, Inc., Agoura Hills, California. AVCON offers a unique technological approach that evolved from the company's work on contracts with Lewis Research Center, and Marshall Space Flight Center. The technology developed in the NASA programs contributed to AVCON's ability to overcome the limitations of early magnetic bearing systems, namely large size and weight, high power consumption and cost. The company's product line embraces a family of very compact, lightweight, power efficient, low cost bearing systems. Beginning in 1989, AVCON worked with Lewis to explore the possibilities of a magnetic bearing system for the turbopump of the Space Shuttle Main Engine. NASA decided to investigate magnetic bearings, which in theory-at that time-offered multiple advantages over conventional rolling element bearings.
回答者:网友
产品精选
我来回答
看不清?换一个
提交答案
相关已解答问题
请问哪种品牌的车身膜比较好?
335双门想贴车身膜,不知是否伤漆?请高人指点?
13款本田锋范手动精英版的,价格85000.送挡泥板、脚垫、座套、下护板、车身膜、车窗饰条.请问贵吗?
奥迪tt贴金黄色车身膜要多少钱?
龙 柳 夏工装载机变速箱泵轮与罩轮之间的间隙怎么调试
汽轮机转子轴向位移的正负值是如何区分的?
汽轮机正常运行中轴向位移增大有哪些原因?
空压机聚才AW100机头轴承是多少的?怎样装起来比较快?
AYJ发动机大瓦安装
请教:含油轴承里面原装的是什么润滑油?
在移动端查看:
急求磁悬浮轴承或磁悬浮飞轮英文资料及译文
搜索问答
还没有汽配人账号?
立即注册
我要提问
精彩推荐
1
末端空调机组用的盘管表冷器和冷凝器它们有什么区别?
2
空压机与储气罐的连接方法
3
电位器WXD3-13的三个脚怎么接线
4
消防管道(卡箍连接)套定额,卡箍套卡箍安装定额,那沟槽管件比如弯头套什么定额?
5
生产加工型企业购生产使用的磨光机、电焊机、磨光片、钻头、面罩等计入哪个会计科目?
6
后八轮自卸车车斗的规格是多少?
7
新年好。请问水泵的铝叶轮和铜叶轮有多大差别?
8
货车帮和运满满哪个好
9
我开了个小型的洗车场,可以同时洗两台车,我想问一下,空气压缩机大概要使用多大功率的啊?
10
如何用压力传感器测液位?压力与液位值如何计算?
周边商家推荐
周边产品推荐
相关问答
怎样进行轮毅轴承的调整?
变速器第一轴后端滚针轴承的作用是什么?它的异常对变速器有什么影晌?
常用载重汽车轮毂轴承与半轴套,是怎样配合的?其损坏原因是什么?
轴承型号中的英文字母含义与区别?
轴承座的选择
单向轴承如何实现单向转动
比亚迪F3的后轮轴承是什么型号
日立ZX200-3发电机轴承是什么型号?
一面带密封圈的深沟球轴承如何密封
关于上海大众朗逸前轮半轴轴承
产品精选
滑动轴承
汽车轮毂轴承
调心轴承
分离轴承
天津轴承
山西轴承
滚针轴承
平面轴承
球轴承
深沟球轴承
优势厂家
平面轴承厂家
万向轴承厂家
轴承座总成厂家
圆锥滚子轴承厂家
关节轴承厂家
iko轴承厂家
瑞典轴承厂家
滚子轴承厂家
推力圆锥滚子轴承厂家
轴承厂家
图片大全
连杆轴承图片
单向滚针轴承图片
进口滚针轴承图片
天津轴承图片
skf轴承图片
光洋轴承图片
山西轴承图片
向心球轴承图片
轴承图片
主轴轴承图片
推荐主题
冲压外圈滚针轴承
关节轴承
常州滚针轴承
南京轴承
分离轴承
平面轴承
球轴承
双列圆锥滚子轴承
推力圆锥滚子轴承
轴承座
本页是网友提供的关于“急求磁悬浮轴承或磁悬浮飞轮英文资料及译文”的解答,仅供您参考,汽配人网不保证该解答的准确性。
协议规则
服务协议
交易规则
注册新用户
帮助中心
网站服务
汽配旺铺
网价查询
商用车EPC查询
营销宝
移动端
手机登录:m.qipeiren.com
iPhone
Android
关于我们
|
汽车配件批发
|
汽车配件图片
|
汽车配件大全
|
汽配问答
|
汽配厂家
|
汽配品牌
|
汽配主题
|
汽配城
|
鄂ICP备14009261号
经营许可证编号:鄂B2-20250371
服务热线:0719-8311727
Copyright © 2005-2026 十堰亿脉科技有限公司 版权所有
鄂公网安备 42030202000345号
电商平台经营者消费品安全与召回共治承诺书