问答
产品
|
公司
|
配件目录
|
EPC底盘号查询
下载手机汽配人
汽配人首页 >
问答首页
铝合金问题
请问用在自行车上的铝合金7005与6061那个好些,好在什么地方?谢谢
问
提问者:网友
|
2017-09-03
最佳回答
7005 versus 6061 Aluminum You may have noticed that there are two types of aluminum listed in the specs for aluminum bikes; 7005 or 6061. Which is the stronger material? Your first answer may be 6061 because you see it on the more expensive bikes. 7005 aluminum is actually the stronger aluminum alloy. This begs the next question, which is the better material? 6061 is of course, or at least that is the opinion of most bike manufacturers. Why is it better? To see the differences one must take a look at the two materials and their properties. In the table below several different aluminum alloys are listed for comparison; 2014, 6061, and 7005. AlloyTrace MetalsTensile StrengthYield StrengthPercent ElongationHBNotes20144.5% Copper 0.8% Silicon 0.8% Manganese 0.5% Magnesium 27,000 psi14,000 psi18%452XXX series aluminum is primarily alloyed with copper.2014-T64.5% Copper 0.8% Silicon 0.8% Manganese 0.5% Magnesium 70,000 psi60,000 psi13%1352XXX series aluminum is primarily alloyed with copper.60611% Magnesium 0.6% Silicon 0.2% Chromium 0.3% Copper 18,000 psi8,000 psi25%306XXX series aluminum is primarily alloyed with magnesium and silicon.6061-T61% Magnesium 0.6% Silicon 0.2% Chromium 0.3% Copper 45,000 psi40,000 psi12%956XXX series aluminum is primarily alloyed with magnesium and silicon.7005-T64.5% Zinc 1.4% Magnesium 0.45% Manganese 0.13% Chromium 51,000 psi42,000 psi13%NA7XXX series aluminum is primarily alloyed with zinc.The tensile strength of the material is the amount of stress that it can take before complete failure, and the yield strength is the amount of stress before the material is permanently deformed (try jumping on an old frame until you bend it and you have exceeded the yield strength of the material). Percent elongation is the amount of deformation that the material undergoes before it breaks and the HB is a measure of the hardness. It should be noted that the ‘T6’ listed after the alloy is the heat treatment of the alloy. T6 refers to a solution treatment and artificial aging of the metal. All bike frames are heat treated even if the manufacturer does not list the T6 behind the grade of aluminum.From the chart you can see that 7005-T6 is slightly stronger than 6061-T6, but stronger than both of them is 2014-T6 and in fact there is another 7XXX series aluminum (7075) that is stronger as well. Why choose 7005 and 6061 then? Bike frames are not made out of solid aluminum, which is how the test samples for comparing material strengths are constructed. A bike frame is made up of tubing that is welded together: welding 7075 and 2014 are almost impossible feats that eliminate them as viable choices for making a bike. That leaves 7005 (a zinc alloy) and 6061 (a magnesium/silicon alloy). The difference between the two is that 7005, because of its high alloy content (over 6%), is harder to manipulate the material and to weld it. This means that with 6061 it is much easier to add strength adding tubing features like triple butting, ovalized tubing, and tapered walls that reduce the weight and improve the strength of the tubing.A final note to put this into perspective is to compare aluminum to the other frame materials. Aluminum is far weaker than both titanium and cro-mo steel, so why use it? Aluminum’s greatest advantage is that it is so light when compared to cro-mo steel and cheap when compared to titanium. This combination of features makes it the choice of material for making light, high-performance frames for a reasonable price.我试一下把重点挑出来:1. 目前铝合金车架普遍使用的材料是7005与6061两种。2. 7000系列主要以锌为主要合金,成分比例达到6%。6000系列主要以镁和矽为主要合金,总成分比例较低。3. 论强度的话7005较强,但只是稍微强一点,从表中可以看出来,yield strength(让铝材永久弯曲变形的力度)只比6061强一点。4. 所有用作车架材料的铝合金都经过热处理T6,5. 但论整体来讲,6061是较好的材料。由于7005含其他金属比例高,所以焊接,处理都比较困难,尤其是7075(后两个数字代表含合金比例)它的比例更高,所以一般是不能用作车架的材料。相比之下,6061由于含其他金属比例较低,因此可以通过异型,各种处理来增加它的强度和减低它的风阻,甚至可以做到3次抽管来减低重量。6. 虽然7005管购买价比较高,但整体来讲6061的生产成本比较高,因为6061所经过的热处理和其他工序比较烦琐复杂。因此6061的车架一般比较贵。也因此大多比较高端的车架(如TCR)也使用6061
回答者:网友
产品精选
我来回答
看不清?换一个
提交答案
相关已解答问题
聚四氟乙烯滤芯焊接温度多少
标准压力表等级划分
空压机润滑油怎么会变成粘稠状,怎样清洗
空压机加热(升温)
出口美国的电源适配器需要什么强制认证EMC,FCC,安规?
PIC16F883单片机的定时器0怎样启动?我的初始化程序见补充部分,要求用C语言写,谢谢!
法兰加工前为什么要热处理?
帮忙算算 法兰 毛坯重量和成品重量
锻造法兰和机加工法兰的区别
304材质不锈钢管材和法兰焊接后,出现裂纹,是怎么回事?请高手回答。
在移动端查看:
铝合金问题
搜索问答
还没有汽配人账号?
立即注册
我要提问
精彩推荐
1
五十铃自动熄火是什么原因啊????
2
长安神骐实际载重多少?我才买的新车载重1.9吨后,车厢后面压下去很多!
3
本田dio化油器的混合比调节调浓动力好还是调稀动力好?
4
上海50拖拉机的重量是多少?
5
依维柯汽车加不起油,提不了速度,没力
6
工字钢承载6吨重4.5米跨距,要用多大的工字钢做横梁和立柱(高度3.5米,平均受力) 工
7
伺服驱动器中控制端口和编码器接口的引脚号是怎么定义的?哪个是引脚1?
8
面包车换前 后轮胎 千斤顶顶在什么地方啊 前麦弗逊 后钢板弹簧 非承载式车身
9
奔驰S350和S600的区别在于什么?
10
日立变频器SJ300..报警E30.6...没输出..怎么解决.......
周边商家推荐
周边产品推荐
相关问答
如何调整康明斯牌柴油机四气门的气门间隙?
变速箱互锁机构的工作原理是什么?
什么是被动悬架?
摩托车的化油器怎么调才最好
丰田赛纳产品如何?
产品精选
帕萨特b4
汽车后视镜
中通客车
气动电磁阀
铰接式卡车
奔驰c230
斯凯孚轴承
铆钉
上海大众配件
深沟球轴承
优势厂家
北方奔驰配件济南厂家
金龙客车厂家
喇叭扬声器厂家
盘式制动器厂家
陕西重汽厂家
龙工装载机厂家
光洋轴承厂家
CF100厂家
车窗饰条厂家
面罩厂家
图片大全
霸龙507图片
汽车水箱图片
特种车图片
国三柴油图片
汽油抽水机图片
菲亚特车图片
普拉多配件图片
驱动轴图片
外壳图片
油门线图片
推荐主题
车桥
汽车膨胀水箱
4102发动机
增压器配件卡箍
五菱之光
汽车安全座椅
汽车弹簧
骨架
内六角螺钉
弯头
本页是网友提供的关于“铝合金问题”的解答,仅供您参考,汽配人网不保证该解答的准确性。
协议规则
服务协议
交易规则
注册新用户
帮助中心
网站服务
汽配旺铺
网价查询
商用车EPC查询
营销宝
移动端
手机登录:m.qipeiren.com
iPhone
Android
关于我们
|
汽车配件批发
|
汽车配件图片
|
汽车配件大全
|
汽配问答
|
汽配厂家
|
汽配品牌
|
汽配主题
|
汽配城
|
鄂ICP备14009261号
经营许可证编号:鄂B2-20250371
服务热线:0719-8311727
Copyright © 2005-2026 十堰亿脉科技有限公司 版权所有
鄂公网安备 42030202000345号
电商平台经营者消费品安全与召回共治承诺书